Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Dvele Fence Installation: The Fort Lauderdale Owner’s Guide
If you own a Dvele home in Fort Lauderdale and the fence has started to lean, separate at the posts, or rot at the base, we can replace it. We install Dvele-compatible fence systems throughout Fort Lauderdale, with most full fence installations running $3,500 – $9,000 depending on linear footage, material type, and whether we’re replacing panels only or pulling and resetting posts. The way most owners find us is by noticing the same thing in the same order: first a soft spot near the ground, then a panel that doesn’t sit flush, then a post that moves when you push on it. South Florida humidity and salt air accelerate all three.
Which Dvele Models This Applies To
Dvele homes, whether built in the Fort Lauderdale area or elsewhere in Florida, typically ship with one of two fence configurations: a composite privacy system or a horizontal slat system built from thermally modified wood or composite boards. The composite systems use a hidden-fastener channel that slides onto aluminum or galvanized steel posts, while the wood-slat systems use a face-mounted bracket with stainless screws. That difference matters because the hidden-channel composite panels cannot be cut down to fit a shorter run without exposing the internal webbing, which compromises the panel’s stiffness. If you’re matching a section rather than replacing the whole run, we need the panel width measured edge to edge, not post center to post center. The current Dvele builds favor a 6-inch-wide slat with a 1-inch gap, but early builds in some subdivisions used a 4-inch slat. They are not interchangeable, and mixing them looks like a patch job no matter how well the color matches.
We are an independent contractor in Fort Lauderdale, not affiliated with Dvele. When OEM panels are backordered, we carry a quality aftermarket equivalent from a South Florida supplier that matches the profile and the color within one shade. For owners, the aftermarket route usually cuts the material wait time in half and drops the per-panel cost by 10 to 15 percent, with no change to the install method.
Styles & brands we work with
Signs Your Dvele Fence Installation Is Failing
- Post wobble that gets worse after rain. This is almost always a footing problem, not a panel problem. Fort Lauderdale’s sandy soil drains fast, which sounds good until a post hole gets over-widened and the concrete collar is narrower than it should be. The post moves, the panel flexes, and the hidden-channel clips start to crack.
- Discoloration or swelling at the bottom six inches of the panel. Composite doesn’t rot, but the end grain of the internal webbing wicks moisture when the panel sits directly on grade or too close to lawn irrigation. Once the webbing swells, the panel can’t be re-cut to salvage it.
- Screws backing out of face-mounted brackets on wood-slat fence. In salt-heavy air, even stainless fasteners lose their bite if they were driven into end grain without a pilot hole. The panel sags, the gap at the top grows, and eventually the slat splits.
- Gaps opening between slats or panels that were flush when the home was delivered. This is usually thermal expansion combined with a bracket that was over-tightened at install. The material can’t move, so it bows instead.
- A gate that drags or won’t latch. The gate frame is the first thing to fail on any Dvele fence in Fort Lauderdale. The hinges and latch are mounted into composite, which doesn’t hold a screw as well as solid wood, and the constant humidity cycles loosen the hardware faster than you’d think.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full Dvele-compatible fence installation in Fort Lauderdale runs $3,500 – $9,000. Here’s what moves the number: linear footage is the biggest driver, then post condition. If the existing posts are sound and level, we can reuse them and the job drops toward the low end. If the posts need to be pulled and re-footed because they were never set deep enough, labor time jumps. A typical Fort Lauderdale yard carries 120 to 180 linear feet of fencing, and at that size you’re usually between $4,800 and $7,200 for a complete composite replacement with new hardware.
Our written price includes the panel material, new posts where needed, the hardware, haul-away of the old fence, and the labor to set, level, and fasten everything. We give you that number before any work starts, and it’s the number on the invoice. Every fence we install in Fort Lauderdale carries the 365-Day Done Right Promise: if the panel warps, the post shifts, or the gate stops latching within a year, we come back and fix it at no charge. That’s in writing, on every project, the same way we’ve done it under the Kingswell standard since 2004.
DIY or Call Us?
You can safely check a few things on your own: whether the post moves when you push it with one hand, whether the panel bottom sits in standing water after a storm, and whether the gate hinge screws have pulled loose enough to see the holes. That tells us a lot before we even come out. What we don’t recommend is pulling panels and re-hanging them yourself. The composite systems use hidden fasteners that are easy to strip, and once a channel clip cracks, the panel won’t seat properly again. On top of that, Fort Lauderdale requires a fence permit when the replacement exceeds 25 percent of the total linear footage, and we handle that paperwork as part of the job.
If you want a straight answer on whether you need full replacement or a section repair, call (754) 551-2922 and describe what you’re seeing. Trevor Nash will tell you what it costs either way, then you decide.
FAQs
A composite Dvele fence in Fort Lauderdale typically lasts 12 to 18 years before the posts or gate hardware start to fail, while the panels themselves often reach 20 years if they were installed with proper clearance from the ground. Wood-slat systems run 8 to 12 years here because the salt air and humidity work on the fasteners and the end grain faster than they do further inland. Call (754) 551-2922 if your fence is showing early wear, and we’ll tell you whether it’s a repair or a replace.
Yes, if the posts are still solid and the failure is limited to one or two panels or a gate frame, we can replace just that section for far less than a full fence. The catch is matching the panel profile, because the slat widths changed between older and newer Dvele builds. Call (754) 551-2922 and we’ll figure out your panel spec before we quote anything.
A standard full fence replacement for a Fort Lauderdale yard takes two to three working days from pulling the old posts to the final gate adjustment, assuming no permit delays. Section repairs are usually done in one day. We give you a defined arrival window before we start, and we leave the job site clean when we’re done.
We keep common Dvele-compatible hardware, gate hinges, latches, and bracket sets on the truck, so most gate and hardware repairs can be completed in a single visit. For full panels, we order to your exact slat width and color from our local supplier, and those typically arrive within five to seven business days. Call (754) 551-2922 and we’ll check availability while you’re on the line.
Written by Trevor Nash, Owner, Penhallow Remodeling Fort Lauderdale at Penhallow Remodeling Fort Lauderdale, serving Fort Lauderdale and nearby areas.
